|
Click on the picture to enlarge
Click HERE for a video presentation of the LaRue Tactical Stealth Sniper System. (High speed internet connection recommended)
Just pull the pins on your old upper, swap it with the Stealth, and begin shooting one ragged hole.
Answering the demands of today's precision AR-Shooter, we designed the Stealth Sniper System with ¾" 100-yard shot groups in mind. Exceeding our expectations, the Stealth has earned a great reputation for it's sub-MOA accuracy, with reports of consistent hits on 4" plates out to 400 yards with 77 grain Mk262 ammunition.
Assembled using our CNC-machined Stealth Billet Upper (LT-007) as the backbone, complete Stealth Uppers are available in 12", 16", 18" & 20" barrel-lengths with the LT handguard length of your choice. NOTE: The 20" Stealth Upper is optimized for use with a rifle-length buffer system. Please let us know, in advance, if you are planning on using a carbine lower (and carbine buffer system) with our 20" Stealth. We want to make sure you will be setup properly. Complete Stealth Uppers come expertly-assembled and tested with Receiver, Free-float Handguard, Barrel, Low-Profile Gasblock and Tube, Mil-Contract M16 Bolt Carrier Group and Charging Handle.
Recommended barrel length / handguard lengths: (see pictures at bottom of page)
20" Barrel: 13.2" & 12.0" Handguards
18" Barrel: 13.2", 12.0", 11.0" & 10.0" Handguards
16" Barrel: 13.2", 12.0", 11.0" & 10.0" Handguards
12" Barrel: 11.0", 11.0" Gooseneck, 10.0", 9.0" & 7.0" Handguards
Components Overview
Upper Receiver:
The LaRue Stealth receiver is an improved-version of the currently fielded mil-spec flat-top receiver. Machined from billet 7075-T6, the Stealth is designed with more of material in critical areas to alleviate past issues of weakness and to stiffen the receiver, maximizing the weapons overall accuracy.
Barrels:
Unless you request bead-blasted stainless, our barrels arrive ION Bonded in black. Ion Bond coating is roughly 5-millionths of an inch thick and roughly 90 Rockwell in hardness (harder than hard-chrome). It won't chip, peel, corrode, and is heat-resistant to over 1200 degrees Fahrenheit.
LaRue Stealth Barrels are Wylde-chambered in 5.56mm, 1-in-8 twist polygonal rifling in medium-weight contour using LW-50 Stainless. In the late 1980's, it was realized that there were erosion and short barrel-life problems with 416 Stainless in the calibers operating at 65K psi. 410 Stainless also had issues. LW-50 became the answer. LW-50 lacks sulphur, which in high quantity, created short throat-life in other Stainless Steels. LW-50 can also be heat-treated to a point that makes it near-optimal in all forms of rifle barrels. LW-50 has been proven for over 15 years, in military and civilian uses ranging from sniper, tactical, target, and other high-performance applications where long life and accuracy are critical.
Free-Float Integrated Rail System:
CNC-machined out of aluminum, LT handguards are available in 7.0", 9.0", 10.0", 11.0", 12.0", and 13.2" lengths. Our two-pin proprietary barrel nut system with its locking anti-slip plate, sets LaRue handguards apart from the competition. Once the rail is properly installed, there is no chance of movement whatsoever. Everything locks into place rock-solid. This is vital when utilizing lasers, optics and other hardware. The side and bottom rails are tucked closer to the barrel, keeping the profile narrower and more streamlined. Special cuts on each rail's end are designed to work with both mil-issue and standard rail covers. LaRue handguards also include a QD sling-swivel socket integrally-mounted at the base of each side for convenient mounting 2-point slings. Additionally, our Free-float Rail system provides an excellent heat-sinking feature that pulls throat-damaging heat away from the chamber area. Another heat-sinking benefit is the elimination of pressure-spikes, which some feel is the cause of a large part of pre-mature bolt failures.
M16 Bolt-Carrier Group:
Assembled to TexasSpecTM our Bolt Carrier Groups use the same mil-spec hardware used military-wide. Additionally, LT assembly enhancements greatly minimize bolt-related failures. Mil-spec gas-key contact areas are precision surface-ground flat for zero gas leakage and then max-staked to eliminate all chances of vibration-induced failures.
Assembly and Testing:
Every LT Stealth Sniper System is precision-assembled and as part of the QA procedure, goes through a final 10-round live-fire function test before being tube-packaged.
TexasSpec is a trademark of Austin Precision Products Inc., Leander, TX
Click here to email a question to LaRue Sales.
Read what the good folks over at SHOOTING USA had to say about the STEALTH, Click HERE
What our customers are saying... I got my new LT Quad-S 16" a couple hours ago and I can't put it down. Thanks! When you spend your money and feel so good about what you got in exchange, you can't beat that feeling. My new LT-011 mounted on a new LMT SOPMOD lower with a LT-110 EOTech and a LT-104 with my 3.3-10 Nikon make a package I'll enjoy for a long time. If this thing shoots as good as it looks, this won't be my last one, bet on it, I am! Thanks to everyone at LaRue Tactical for making this such a great experience.
Steve XXXXX
A dyed in the wool LT believer
RANGE REPORT
Mark, Here's the range report. Precision Rifle Concepts class at Ben Avery Range, Phoenix, Arizona, April 14 and 15. Mostly Remington 700s, Winchester 70s, or equal, 4 AR formats, 2 of those .223 caliber. Shooting 50-300 yards from bench, prone (supported and unsupported) kneeling, sitting and squat, over, under and around obstacles. Weather was very windy both days. LT Stealth 16 with Nikon 3.3x10 consistently shot 3-3.5" groups at 300 yards. The daylight part of the shoot ended with a speed/precision drill shooting four 5/8" fluorescent dots at 50 yards. Shooters lined up, then moved quickly to the bench and fired 4 rounds, first one to hit all four dots wins. Chock up one win for the Stealth. The instructor decided to make it a little more fair for the bolt guns and repeated the drill with the auto loaders only having one round loaded in a magazine. I only had two mags, so I had to reload two mags in the middle of the drill. No matter, chock up another win for the Stealth. The final test for the Stealth came under failing light with a one round 50 yard shot from a bench on a "called" shot by the instructor at a perpetrators head, on command. The line was to hold "ready" to fire for up to 3 minutes and fire on command at a specific body part. The called target was a life sized eye. The Stealth nailed the pupil on command. The other shooters were fairly well impressed with the Stealth by this time so everyone gathered for a closer look. I removed the scope with its SPR mount and remounted it to the rifle, then we repeated the drill. No one could believe that the second round hole was touching the first.
My LT Stealth is everything I hoped for, a CQB rifle with precision capabilities to 300 yards. Thanks again and watch for my order of a 10.5" upper!
Steve XXXX
Rating: 5 Bullets (BEST!)
Title of Review: Ready To Fight
Review: I have been extremely pleased with the quality and reliability I have experienced using this upper. No failures and great accuracy. What more do you need? Thanks to all at LaRue for your dedication to our country and those who fight for it.
Call early and we'll most likely ship it that afternoon. :-)
Write a review of your STEALTH upper!
 |
 |
Return to Catalog
|
Advanced Search 
