SKU: B310
10 In Stock The Complete B3 Kit with digital controller . A professionally designed ortho hydrogen cell, now comes cleansed, conditioned ready to go! approved by Bob Boyce®. Everything you need, for a complete install, except water & electrolyte. Comes with a Volo FS2-HHO-Edition circuit for 1996 and newer cars & trucks, or a D-EFIE circuit for OBD I cars, 1987-1995. Carb. cars & trucks need no circuits. Comes with a dash board mounted digital ammeter & switch. Comes with down-loadable instructions. With the FS2, you don't need an EFIE, a O2 sensor circuit, a MAP/MAF adjuster circuit, just a OBD II car ( 1996 and newer) A "U-assemble kit. If you have older car pre - 1996 we have EFIE's and MAP adjuster than you can install. The cell is "guaranteed" to last 10 years. (see photo of all the parts you will get.) You can expect about 25% better MPG savings, if installed correctly, some get better. In Colombia the B3 cell kits care getting 50% to 100% better mileage, do to the less refined gas and diesel they have down south, more carbon for the ortho hydrogen to bond too! The 'ortho' hydrogen these cells make like to cling to the hydro-carbon chains of molecules and tears them all apart in the combustion chamber leaving real clean emissions. The more carbn the fuel has the better results can be seen!
The Super B3 Complete Kit. Everything you need, for a complete install, except water & electrolyte. Comes with a FS2 HHO-Edition Fuel Saver Electronic Circuit, and on dash digital ammeter & switch. Comes with downloadable instructions. Finally a break through, with the FS2, you don't need an EFIE, a O2 sensor circuit, a MAP/MAF adjuster circuit, just a OBD II car ( works on 1996 or newer cars) If you have a 87' to 95 year car, OBD I, we can supply you with a D-EFIE. Most model cars & trucks are available. See List Below. A "U-assemble kit. Install time about 4-8 hours. All electronics come pre-assembled, only few wires need assembling in place between your dashboard and engine compartment. Assembly photos and instructions are down-loadable. I would like to learn more about adding a hydrogen booster to my car. Water as a fuel? Read about the inventors and history of hydrogen. We guarantee the cell will last up to 10 years, if you do not install by the exhaust manifold, or by the cooling system , and no more than 18 amps max. Makes the best highest quality gas at 8 amps. The B3 cell system is perfect for a 4 cylinder or 6 cylinder engines. It will work on V8, 5 liter engines, but you may want to go to a bigger circulating cell system.
B3 = Bob Boyce Booster , before buying read : HYDROGEN CELL REVIEW
Parts List (see photo of that you get)
1) B3 Assembly (7 plates, screws & parts bag, cap, elbow 90º, top & bottom case, 2 terminals, 4 nuts, 4 washers)
2) Safety Bubbler/Spark Arrestor
3) PWM P30 ( pulse width modulator, in alum. case, as in photo.)
4) Hydroxy Gas Dryer, 1 micron filter/ spark arrestor.
5) 30 Amp Relay & pre-made wiring harness, easy to install.
6) ON/OFF dash board switch
7) Digital Ammeter, small box with on/off switch & Amp adjust
8) FUSE (30 amp)
9) Piggyback FUSE connector
10) Volo FS2 HHO-Edition, Electronic Fuel Saver Circuit ( List your vehicle's make, model and year, below) 96'-2009 cars & trucks. If you have a 87' to 95' year car you have OBD I and the Volo FS2 will not work for you, so we replace with a D-EFIE circuit. DEFIE can we used on the O2 or MAF/MAF sensor.
11) 8' of Hose 3/8" ID reinforced poly clear hose.
Dim. 9.5" x 7.5" x 3.25"
The B3 Kit comes with the *NEW VOLO FS2 HHO-Edition, Electronic Fuel Saver Circuit that comes programmed with a highly tuned map and a set of EPROM addresses that directly affect fuel efficiency. When the ECU attempts to read the specific EPROM address, the FS2 circuit patches the factory value with one from its tuned map. It's exclusive patching algorithms to increase fuel efficiency across the map by up to 18%. The FS2 specifically changes values that affect fuel delivery and timing, based on readings from the MAP/MAF, IAT, CIT and all O2 sensors. Works along with your hydroxy gas generator.
Easy Installation, only 4 to 6 wires! Locate the OBD-II port, use the included connectors, or solder and you're done. Can still be used with your OBD II plugged in your excellent engine on board monitor : Scangauge II.
ATTENTION INTERNATIONAL CUSTOMERS : Please verify your vehicle is OBD-II compliant before making a purchase. 1996-2009 Cars and trucks are OBD II. Will not work with OBD I (1987-95) cars.
To order the right FS2 circuit for your make and model car or truck go to this page : Make & Mode & Year and find your car in the list, copy and paste your car and model and then paste in the text box below. If your car is not in the list, then I'm sorry they don't make a circuit, yet for your car.
* This circuit is an "enhancement circuit" and does not touch the ECM or change it's emission system, therefore making it legal for you to try it out and go green. Your emissions will be so clean from a good running HO booster, you will be able to pass any emission test with way cleaner emissions, hands down. Consult with your local SMOG man before testing, he may be for or against change. Terms & conditions of Hydrogen Garage LLC.
10 In Stock
