|
EFIE
|
|
18/1 Fuel Enhancer
The 18/1 Fuel Enhancer. A new improved EFIE using modern micro electronics. Designed by a electronic wizard friend. Guaranteed to work as described or your money back. (Comes pre-assembled, no soldering) MADE IN USA
PRICE: $60.00
|
|
DIY Dual O2 Sensor U-Solder Kit (EFIE)
The "Do It Yourself" Dual O2 Sensor Fuel Saver Circuit "
This circuit uses one LM324, a Quad Amplifier. This circuit uses 2 amps per O2 sensor, so it will work to adjust two O2 sensors. You can use it for a OBD II car 96 and on. One side adjusts the PRE cat. O2 sensor and the 2nd one adjusts the POST cat. O2 sensor. You can also use just one side of the circuit for a OBD I vechicle 87-95.
PRICE: $35.00
|
|
DIY Dual O2 Sensor WIRE Kit
The designer of the DIY Dual O2 circuit recommends shelided wire, grounded to one side only. It is hard to find single cond. shellded wire. We are selling 22 gauge copper stranded wire and sheilded wire.
PRICE: $12.00
|
|
DSF Fuel Saver HHO Edition
The NEW! Volo DSF Fuel Saver HHO Edition Circuit - FS2 (released 8/09)
These LOW PRICE DSF Circuits works by an exclusive process of "Dynamic Soft-Flashing" the ECU. The new FS2 was specially designed for the addition of hydroxy gas generators.
New introductory sale price - $94.95! Check availability for your Make, Model, Year car or truck.
Each "DSF Fuel Saver" comes programmed with a highly tuned map and a set of EPROM addresses that directly affect fuel delivery and timing, based on readings from the MAP/MAF, IAT, and O2 sensors. When the ECU attempts to read the specific EPROM address, the DSF circuit patches the factory value with one from its tuned map. Easy to install.
Your Satisfaction is Guaranteed!
PRICE: $94.95
|
|
Dual O2 Sensor Circuit & box Soldered (EFIE)
"The Dual O2 Sensor Fuel Saver Circuit " (all soldered up, tested calibrated to one volt & ready to install) Designed by Claudio Cabete aka "Electrojolt" This circuit uses one LM324, a Quad Amplifier. This circuit uses 2 amps per O2 sensor, so it will work to adjust two O2 sensors or one. You can use it for a OBD II car 96 and on. One side adjusts the PRE cat. O2 sensor and the 2nd one adjusts the POST cat. O2 sensor. You can also use just one side of the circuit for a OBD I vechicle 87-95.
PRICE: $85.00
|
|
EFIE Electronic Fuel Injection Enhancer Circuit
Comes soldered up and ready to install just 4 wires. This circuit has been selling since the 80's and modified to the current circuit. Thousands of motorists have installed them. Only works on O2 sensors with 1 volt signals.
PRICE: $60.00
|
|
H2 Systems Enhancer
"H2 Systems Enhancer" was designed to properly introduce hydroxy gas into a vechilces engine at the most appropriate time. The H2 Systems Enhancer will maintain factory sensor settings until the Enhancer delay times out. It has adjustable pots. for "Air Intake Temps" (I.A.T.) and "Coolant Temp. Sensors" ( C.T.S.)
PRICE: $180.00
|
|
EFIE
|
H2 Enhancer
|
|
|
H2 Systems Enhancer
"H2 Systems Enhancer" was designed to properly introduce hydroxy gas into a vechilces engine at the most appropriate time. The H2 Systems Enhancer will maintain factory sensor settings until the Enhancer delay times out. It has adjustable pots. for "Air Intake Temps" (I.A.T.) and "Coolant Temp. Sensors" ( C.T.S.)
PRICE: $180.00
|
