SKU: B3K
3 In Stock The Complete B3 Kit. Everything you need, for a complete install, except water & electrolyte. Comes with a DS2 Fuel Saver Electronics, and on dash DC Ammeter & switch. Comes with downloadable instructions. Finally a break through, with the DS2, you don't need an EFIE, a O2 sensor circuit, a MAP/MAF adjuster circuit, just a OBD II car ( works on 1996 or newer cars) Most model cars & trucks are available. See List Below. A "U-assemble kit. Install time about 8 hours. All electronics come pre-assembled, only few wires need assembling in place between yourt dashboard and engine compartment. Assembly photos and instructions are down-loadable. I would like to learn more about adding a hydrogen booster to my car.Water as a fuel? Read about the inventors and history of hydrogen.
Parts List
1) B3 Assembly (7 plates, screws & parts bag, cap, elbow 90º, top & bottom case, 2 terminals, 4 nuts, 4 washers)
2) Safety Bubbler/Spark Arrestor Assembly ( clear acrylic tube, 2.5” OD, 10“ tall, top & bottom plumber’s cap and hose clamp, elbow 90º , 6’ of 3/8” ID clear poly chemical resistant hose.)
3) PWM Cell-X-Siter ( pulse width modulator, 2 red adjustment knobs, 2 terminals )
5) 30 Amp Relay
6) 12v. lighted switch
7) DC Ammeter
8) FUSE link
9) Piggyback FUSE connector
10) DS2 Electronic Fuel Saver Circuit ( List your vehicle's make, model and year, below)
11) Wire Kit - 10’ of white & black 10 gauge wire, 4’ of 22 gauge wire.
Only Black top and black bottom case in stock right now (11/01/09)
The B3 Kit comes with the NEW "DSF2 Fuel Saver" that comes programmed with a highly tuned map and a set of EPROM addresses that directly affect fuel efficiency. When the ECU attempts to read the specific EPROM address, the DSF circuit patches the factory value with one from its tuned map. It's exclusive patching algorithms to increase fuel efficiency across the map by up to 18%. The FS1 specifically changes values that affect fuel delivery and timing, based on readings from the MAP/MAF, IAT, and O2 sensors. Works along with your hydroxy gas generator.
Easy Installation, only 4 to 6 wires! Locate the OBD-II port, use the included connectors, or solder and you're done. Can still be used with your OBD II plugged in your excellant engine on board monitor : Scangauge II.
ATTENTION INTERNATIONAL CUSTOMERS : Please verify your vehicle is OBD-II compliant before making a purchase. 1996-2009 Cars and trucks are OBD II. Will not work with OBD I ( 1987-95) cars.
To order the right DS1 circuit for your make and model car or truck go tho this page : Make & Model and find your car in the list, copy and paste your car and model and then paste in the text box below. If your car is not in the list, then I'm sorry they don't make a circuit, yet for your car.
* Please note : These items are not stocked and are ordered, so allow one week extra for delivery of the DS1 circuit. We can ship the B3 Kit right away, but the circuit comes a week later. You will recieve 2 packages, with the B3 Kit. Also note the packing in the photo may come different, in black or a blue box. The box size is approx. is 1.5" x 1.5" x .5"
* This circuit is an "ehnancement circuit" and does not touch the ECM or change it's emission system, therefore making it legal for you to try it out and go green. Your emissions will be so clean from a good running HO booster, you will be able to pass any emission test with way cleaner emissions, hands down.
3 In Stock
